Electrical Service Upgrade in Schaumburg: More Power for How You Live Today

Many homes in Schaumburg still run on 60 or 100 amp service. That was enough when the house was built. It is not enough for central air, an EV charger, a hot tub or a finished basement. A service upgrade raises the power your home can safely draw from the grid.

Energy Co. replaces the meter socket, the service mast or underground feed, the grounding and the main panel when needed. We pull the permit and coordinate the disconnect and reconnect with ComEd.

Electrical service upgrade in Schaumburg: new service mast and meter socket being installed on a home

Service Upgrade vs. Panel Upgrade: What Is the Difference?

A panel upgrade replaces the breaker box inside your home. A service upgrade goes further. It increases the amperage that comes into the house, from the utility connection through the meter to the main breaker.

If your service is 100 amps or less, a new panel alone will not add capacity. We check your service size, your current load and your plans, then tell you which upgrade you actually need.

How an Electrical Service Upgrade Works

An electrical service upgrade in Schaumburg follows six steps:

  1. Load calculation: we add up your current and planned appliances to size the new service.
  2. Permit: we file the electrical permit with the Village of Schaumburg or your municipality.
  3. ComEd request: we submit the service change and schedule the disconnect with the utility.
  4. Installation day: we replace the meter socket, the mast or riser, the grounding and the panel if needed.
  5. Inspection: the village inspector checks and approves the new service.
  6. Reconnect: ComEd sets the meter and your power comes back on.

Signs Your Home Needs a 200 Amp Service Upgrade

Your home may need more service capacity if you notice:

  • Main breaker trips when the AC and dryer run together
  • Lights dim when large appliances start
  • No room to add a circuit for an EV charger or hot tub
  • A 60 or 100 amp main breaker or an old fuse box
  • A rusted meter socket or a leaning service mast

Many 1960s and 1970s ranch homes in Schaumburg and Hoffman Estates show several of these signs.

New 200 amp meter socket with service disconnect on a brick home after a service upgrade
Satisfied Customers
0 %
New underground electrical service and meter installed on a home before final grading

We Coordinate With ComEd So You Do Not Have To

A service upgrade needs the utility to cut power and set a new meter. We file the request with ComEd, share the load details and book the outage window. Most homes are without power for one working day.

We plan the work so your refrigerator and sump pump are off for as short a time as possible. If you have a medical device that needs power, tell us and we will plan around it.

What Your Electrical Service Upgrade Includes

A complete electrical service upgrade usually includes:

  • A new meter socket rated for the new amperage
  • A new service mast or riser for overhead lines, or new conduit for an underground feed
  • Upgraded grounding and bonding to current code
  • A new main panel or main breaker when required
  • Surge protection at the panel, if you want it

We size every part together, so the whole path from the meter to the panel carries the same rating.

Permits, Inspection and Records for Your Home

Every service upgrade needs a permit and an inspection before ComEd restores power. We pull the permit, meet the inspector and handle any correction on the spot.

You get the approved permit, a labeled panel schedule and photos of the new service. These records help when you sell your home or file an insurance claim.

Running out of power for an EV charger, AC or new addition? Energy Co. upgrades your electrical service in Schaumburg with permits and ComEd coordination included.

COMMON QUESTIONS

Frequently Asked Questions

A service upgrade involves the utility, the village and your home. Here are the questions homeowners ask us most often:

It increases the amount of power your home can draw from the utility. We replace the parts between the power line and your main breaker, such as the meter socket, mast and grounding.

Check the number on your main breaker, often 60, 100 or 200 amps. We confirm it during our visit and check the meter socket and service cable too.

Most homes with central air, electric appliances and an EV charger do well with 200 amps. We run a load calculation to confirm the right size for your plans.

Most residential service upgrades take one working day. ComEd disconnects power in the morning and reconnects it after the village inspection passes.

Yes. We submit the service request, share the load details and schedule the disconnect and reconnect with ComEd.

Yes. The Village of Schaumburg requires an electrical permit and inspection. We file it and meet the inspector on the day of the work.

Often, yes. Moving a meter or going underground needs approval from ComEd and sometimes extra trenching. We review the options during the estimate.

Not always. If your panel is in good condition and rated for the new service, we may keep it. Old Federal Pacific, Zinsco or fuse panels are usually replaced.

Yes. We upgrade single-phase and three-phase service for shops, offices and light industrial spaces across Chicago and the Northwest Suburbs.